Sierra Wireless AirLink FXT Series Guia do Utilizador Página 83
- Página / 142
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
WA_DEV_FEX20_UGD_002 Rev 004 March 08, 2011 83
Fastrack Xtend User Guide
Communicating with the Fastrack
Xtend
Feature/Function
AT Command
Response
Description
AT+WMBS=<Band>,0
OK
Band switch is accepted; the
Fastrack Xtend has to be reset for
the change to be effective.
AT+WMBS=<Band>,1
OK
Band switch is accepted and the
GSMS stack has been restarted.
AT+WMBS=<Band>
+CME ERROR: 3
Band selected is not allowed.
Receive a call
ATA
OK
Answer the call.
Initiate a call
ATD<phone
number>;
(Do not forget the « ;
» at the end for
« voice » call)
OK
Communication established.
+CME ERROR: 11
PIN code not entered (with +CMEE =
1 mode).
+CME ERROR: 3
AOC credit exceeded or
communications is already
established.
Initiate an emergency
call
ATD112;
(Do not forget the « ;
» at the end for
« voice » call)
OK
Communications established.
Hang up
ATH
OK
Communication has
been loss
NO CARRIER
Store the parameters
in EEPROM
AT&W
OK
The configuration settings are stored
in EEPROM (non-volatile memory).
* The command AT+CMEE=1 switches to a mode that enables a more complete error diagnostic.
9.8. Echo Function
If no echo is displayed when entering an AT Command, it could mean either of the following:
The “local echo” parameter of your communication software (HyperTerminal) is disabled.
The Fastrack Xtend echo function is disabled.
To enable the Fastrack Xtend‟s echo function, enter the AT Command ATE1.
When sending AT Commands to the Fastrack Xtend using a communication software such as
HyperTerminal, it is recommended to:
Disable the “local echo” parameter of your communication software.
Enable the Fastrack Xtend‟s echo function (use the ATE1 command).
In a machine-to-machine communication with the Fastrack Xtend, it is recommended to disable the
Fastrack Xtend‟s echo function (using the ATE0 AT command) in order to avoid useless embedded
module processing.
Refer to document [7] Firmware 7.4a
AT Commands Manual (Sierra Wireless Software Suite
2.31)/Firmware 7.4 AT Commands Manual (Sierra Wireless Software Suite 2.30) for more information
about the ATE0 and ATE1 AT Commands.
9.9. DC-IN Detection
Refer to section 15.5 DC-IN Detection for more information on how DC-IN detection is done using AT
commands.
- AirLink FXT Series 1
- Fastrack Xtend User Guide 1
- Important Notice 2
- Safety and Hazards 2
- Limitations of Liability 2
- Patents 3
- Copyright 3
- Trademarks 3
- Contact Information 3
- Document History 4
- Contents 6
- List of Figures 11
- List of Tables 13
- 1. Overview 16
- 1.2. Overall Dimensions 19
- 1.4. Connections 20
- 1.5. Interfaces 20
- 2. Features and Services 22
- Features and Services 23
- 2.2. Supported Bands 26
- 2.4. Protection 27
- 3.2. RF Functionalities 29
- 3.3. Operating System 29
- 4. Technical Specifications 30
- 5. Interfaces 32
- , Vref = 2.8V 34
- , Vref > 2.8V 37
- 5.1.1.2. ON/OFF Pin 38
- 5.1.2. Serial Interface 39
- 5.1.2.2. Autobauding Mode 43
- 5.1.2.4.2. Speaker 45
- 5.1.3. USB Interface 46
- 5.2. Back Interface 47
- 5.2.2. Main RF Interface 48
- FXT010) 49
- 6. Signals and Indicators 53
- 6.4. LED Status Indicator 55
- 6.5. Real Time Clock (RTC) 56
- 7. Expansion Card 57
- Expansion Card 58
- 7.4.1. Ethernet 61
- 7.4.1.2. Board Architecture 62
- 7.4.1.4. Power Supply 63
- 7.4.2. IO+GPS 64
- 7.4.2.4. Power Supply 67
- 7.4.2.7. External Antenna 67
- 7.4.2.8. GPS RF Performance 68
- 7.4.3.2. Board Architecture 69
- 7.4.3.4. Power Supply 71
- 7.5. Expansion Card Removal 72
- 8. Using the Fastrack Xtend 73
- 8.2. Getting Started 74
- 8.4. Operational Status 78
- 9.1. Communications Testing 79
- 9.5. Switching Bands 81
- 9.8. Echo Function 83
- 9.9. DC-IN Detection 83
- Firmware 7.4a 84
- 11.2. Receiving “ERROR” 86
- 12. Power Consumption 88
- 12.2. Working Mode Features 89
- (FXT009) 90
- (FXT003) 92
- 12.8.1.1. Equipment 99
- 12.8.1.2. SIM Cards Used 100
- Power Consumption 101
- Fastrack Xtend on Trucks 103
- 14.1. Standard Accessories 105
- 14.3. Optional Battery 105
- Battery Accessory 107
- 15.3. Charging Time 109
- 15.2. LED Indicator 109
- 15.5. DC-IN Detection 110
- Other Information 111
- Recommended Standards 112
- 16.3.2.1. Life Stress Test 114
- Recovery time: 3 hours 115
- 18. Safety Recommendations 121
- 18.2. Battery Safety 122
- 18.3. Vehicle Safety 122
- 18.4. Care and Maintenance 122
- 18.5. Your Responsibility 123
- 19. Reference Documents 124
- 20. List of Abbreviations 126
- List of Abbreviations 127
- 21. Appendix A: Packaging 128
- 21.2.1. GSM Antenna 130
- 21.2.2. GPS Antenna 131
- 21.2.3. Serial Data Cable 132
- 21.2.5. USB Cable 134
- 21.2.7. Package 135
- 21.2.8. Two Holding Bridles 135
- 23. Appendix C: Safety 139
- 23.2. General Safety 140
- 23.2.6. Children 141
- 23.2.7. Blasting Areas 141
Manuais e produtos relacionados com Gateways/controladores Sierra Wireless AirLink FXT Series
(13 páginas)
(2 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.452 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais